How to use optical fiber recoater

Kategori

produk baru

LDC-100 बड़े व्यास ऑप्टिकल फाइबर क्लीवर * क्लैडिंग व्यास 80μm ~ 600μm फाइबर के लिए लागू *वैक्यूम पंप वी-नाली फाइबर डालने के लिए सुविधाजनक है *डी टिकाऊ ब्लेड, जीवनकाल 20000 से अधिक बार *डेटा भंडारण 4000 समूह * उपयोगकर्ता के अनुकूल जीयूआई मेनू, संचालित करने में आसान lebih
S-22 Multi-Core Fiber Fusion Splicer Splicer F fusi Serat M ulti - inti Otomatis Sepenuhnya Pertama di Cina _ lebih
Polarisasi Mempertahankan (PM) Serat Fusion Splicer S-12 * Inti inti keselarasan, rendah splicing loss * Endview dan Profil observasi dan keselarasan * Busur kalibrasi otomatis dan penyambungan * PM serat 45 dan 90 derajat alignment lebih
S-37 LDF Speialty Fiber Fusion Splicer SHINHO S-37 adalah model terbaru yang kami kembangkan, dapat menyambungkan diameter kelongsong serat dari 125 hingga 400μm dengan kehilangan sambungan yang rendah. Kami melengkapi mesin dengan 3 pemegang serat yang berbeda, dan 2 pasang elektroda cadangan. lebih
pita serat fusion splicer x950 Pita serat fusion splicer untuk 2-12 core Penyelarasan serat yang akurat, kehilangan splicing yang rendah Desain industri yang kuat, mudah dioperasikan lebih
inti ke inti penyelarasan serat fusion splicer x900 enam motor fusion splicer, inti nyata ke teknologi penyelarasan inti. Splicing 6s, pemanas 16 detik, mengidentifikasi jenis serat secara otomatis. digunakan untuk proyek telekomunikasi / telekomunikasi. lebih
kuat multi fungsi arc fusion splicer s16 desain industri yang kuat, anti guncangan, anti debu dan tahan air. dudukan multi fungsi untuk serat telanjang, kabel patch, kabel drop dll. penyambungan dan pemanasan cepat, kalibrasi busur otomatis. lebih
SHINHO X-18 रिबन फाइबर थर्मल स्ट्रिपर शिन्हो X-18 थर्मल स्ट्रिपर एक नव विकसित हाथ से आयोजित थर्मल स्ट्रिपर है, जिसे विशेष रूप से 12 फाइबर तक रिबन केबल के जैकेट के गैर-विनाशकारी थर्मल स्ट्रिपिंग के लिए डिज़ाइन किया गया है। रिबन फाइबर स्प्लिसिंग कार्य के लिए एक अच्छा और विश्वसनीय उपकरण। lebih

How to use optical fiber recoater

2024-05-31

How to use the optical fiber recoater?

First, place the optical fiber to be coated in the position shown in the figure below, and align the center of the coated optical fiber with the injection port so that the machine can coat evenly on the left and right.

Before the coating operation, you need to inject a small amount of UV curing material into the glass mold of the optical fiber recoater, and confirm that there are no bubbles in the UV curing material. Open the mold cover, press the Purge key, and run the pump. Inject the UV curing material from the bottle into the glass mold. After the injection amount is as shown in the figure, press the Purge key again to stop the injection.

Close the mold cover, open the upper lamp cover, and press the Start key to inject the resin. From the window shown in the figure, you can observe the UV curing material reaching the target point of the optical fiber. Press the Purge key to pause the coating if the UV curing material has reached the target point and the machine has not stopped. If the UV curing material has not reached the target point, press the Add key to increase the injection amount. After reaching the target point, press the Add key again to stop the injection.

Note: 1. When injecting UV curing glue, be sure to open the upper lamp cover. Since the injection time is controlled by the parameter setting time, it is impossible to completely and accurately cover the target optical fiber. 2. If the entire glass mold is opened after the UV curing material is injected, the material will leak out of the groove, so it needs to be re-coated.

When the coating operation is completed, close the upper lamp cover and press the Start button to turn on the UV curing lamp. The optical fiber can be removed only after the buzzer prompts.

Note: When the UV lamp is working, be sure not to open the glass mold and the upper lamp cover. Otherwise, it will affect the curing effect.

After the optical fiber is taken out, immediately wipe the upper and lower glass molds of the optical fiber recoater with dust-free cotton or dust-free cloth containing alcohol. If the UV curing material remaining on the glass mold is not removed, the curing material will stick to the upper and lower glass molds and damage the surface finish of the glass mold. When re-coating, irregular coating will be formed. The specific cleaning operation is shown in the figure below.

Note: Place a dust-free cloth or soft tissue between the upper and lower glass molds when storing or not using the machine.

The FR-100 optical fiber recoater independently developed and produced by Xianghe Communication has a variety of coating programs to choose from, automatic cleaning function, and convenient resin replacement and addition.

Sebelumnya :
"Unite and Climb to the Top"-----2024 Team-building activities of Shinho Communication concluded successfully
Berikutnya :
What is hollow core fiber