Application of large diameter fiber fusion splicer in laser source maintenance

Kategori

produk baru

LDC-100 बड़े व्यास ऑप्टिकल फाइबर क्लीवर * क्लैडिंग व्यास 80μm ~ 600μm फाइबर के लिए लागू *वैक्यूम पंप वी-नाली फाइबर डालने के लिए सुविधाजनक है *डी टिकाऊ ब्लेड, जीवनकाल 20000 से अधिक बार *डेटा भंडारण 4000 समूह * उपयोगकर्ता के अनुकूल जीयूआई मेनू, संचालित करने में आसान lebih
S-22 Multi-Core Fiber Fusion Splicer Splicer F fusi Serat M ulti - inti Otomatis Sepenuhnya Pertama di Cina _ lebih
Polarisasi Mempertahankan (PM) Serat Fusion Splicer S-12 * Inti inti keselarasan, rendah splicing loss * Endview dan Profil observasi dan keselarasan * Busur kalibrasi otomatis dan penyambungan * PM serat 45 dan 90 derajat alignment lebih
S-37 LDF Speialty Fiber Fusion Splicer SHINHO S-37 adalah model terbaru yang kami kembangkan, dapat menyambungkan diameter kelongsong serat dari 125 hingga 400μm dengan kehilangan sambungan yang rendah. Kami melengkapi mesin dengan 3 pemegang serat yang berbeda, dan 2 pasang elektroda cadangan. lebih
inti ke inti penyelarasan serat fusion splicer x900 enam motor fusion splicer, inti nyata ke teknologi penyelarasan inti. Splicing 6s, pemanas 16 detik, mengidentifikasi jenis serat secara otomatis. digunakan untuk proyek telekomunikasi / telekomunikasi. lebih
kuat multi fungsi arc fusion splicer s16 desain industri yang kuat, anti guncangan, anti debu dan tahan air. dudukan multi fungsi untuk serat telanjang, kabel patch, kabel drop dll. penyambungan dan pemanasan cepat, kalibrasi busur otomatis. lebih
SHINHO X-18 रिबन फाइबर थर्मल स्ट्रिपर शिन्हो X-18 थर्मल स्ट्रिपर एक नव विकसित हाथ से आयोजित थर्मल स्ट्रिपर है, जिसे विशेष रूप से 12 फाइबर तक रिबन केबल के जैकेट के गैर-विनाशकारी थर्मल स्ट्रिपिंग के लिए डिज़ाइन किया गया है। रिबन फाइबर स्प्लिसिंग कार्य के लिए एक अच्छा और विश्वसनीय उपकरण। lebih
Fiber Optic Cleaver X-50D Presisi Tinggi Ukuran kecil & ringan, mudah dioperasikan. Presisi tinggi dan kinerja yang stabil. Lebih dari 48.000 waktu masa pakai blade, panjang serat yang dibelah 5~20mm. Bahan berkualitas tinggi lebih

Application of large diameter fiber fusion splicer in laser source maintenance

2025-04-17

In the field of industrial laser sources, large diameter fiber is widely used in core components such as pump sources, combiners, and QBH interfaces because of its high power transmission capability. Fiber connection failures (such as breakage and excessive loss) of these components directly affect laser performance and even cause equipment downtime. Traditional splicers are difficult to meet the splicing needs of large core fiber, while large diameter fiber splicers have become key equipment for laser maintenance due to their unique technical advantages. Shinho S-37 large diameter fiber fusion splicer is popular with laser soucer repair industry.

Next, we will analyze the application technology of large core splicers in laser core component maintenance.

Application in laser core component maintenance

(1) Pump source pigtail repair: efficient splicing of multimode optical fiber
1. Typical failure scenarios
The semiconductor pump source pigtail often causes the fiber to overheat and melt due to poor heat dissipation (such as the case of the pigtail burning of the Keplin 1500W laser), and the 200/220μm multimode pigtail needs to be replaced.
2. Repair effect

The welding loss is stable below 0.02dB, and the output power fluctuation of the pump source after repair is less than 1%, which meets the long-term operation requirements of industrial-grade lasers.

(2) Repair of fiber inside the combiner: Multi-fiber parallel fusion technology
1. Complex working conditions
The 7×1 pump combiner contains 7 200/220μm pump fibers and 1 20/400μm signal fiber. When fusion splicing, the concentricity of fibers with different diameters needs to be handled (deviation <2μm), and the fusion point is prone to overheating (temperature rise >30℃) due to cladding light leakage.
2. Key technical solutions
Cladding corrosion process: The 200μm pump fiber is etched with hydrofluoric acid (concentration 30%, time 5 minutes) to reduce the cladding diameter to the cladding size of the 400μm signal fiber (400μm), eliminating the fusion gap caused by the diameter difference.

Step-by-step splicing strategy: first splice the signal fiber with a single pump fiber (loss < 0.05dB), then splice the remaining pump fibers in sequence. After each splicing step, use thermal conductive glue (aluminum nitride-based) to fill the gap to reduce heat accumulation.

(3) QBH interface fiber repair: high-power transmission reliability guarantee
1. Failure mode analysis
The QBH interface caused the 200/220μm fiber to wear and break due to frequent plugging and unplugging, or the core burned under high power due to the lack of end caps (such as the QBH failure of the Chengying laser welding machine).
2. Fusion optimization solution
End cap fusion technology: 100μm quartz end caps are fused at the end of the optical fiber to increase the energy receiving area (reduce the energy density to <10kW/cm²) to avoid core damage under high power.
Cladding light stripping: High refractive index glue (refractive index 1.5) is applied 20mm after the fusion point to strip the leaked cladding light (stripping efficiency >95%) and reduce thermal damage to the connector.

The large diameter fiber fusion splicer effectively solves the multimode fiber fusion problem in the maintenance of laser core components through technological innovation. In the repair of key components such as pump sources, combiners, and QBH interfaces, its fusion loss control, thermal management capabilities, and reliability assurance technologies have significantly improved the maintenance efficiency and equipment operation stability.

Berikutnya :
Hollow-core fiber(HCF) development&application trend